Microwave ovens are a standard kitchen equipment that can be utilized to cook dinner, reheat, and defrost meals. They’re comparatively straightforward to make use of, however eradicating them from the wall is usually a bit more difficult. If you’re planning to maneuver or transform your kitchen, you could have to take away your overhead microwave. Listed below are a number of recommendations on how you can do it safely and simply.
Earlier than you start, just remember to have the entire crucial instruments and supplies. You have to a screwdriver, a wrench, and a pair of pliers. You may additionally want a ladder in case your microwave is mounted excessive on the wall. After you have gathered your instruments, you possibly can start the removing course of. First, unplug the microwave from {the electrical} outlet. Then, take away the mounting screws which can be holding the microwave to the wall. As soon as the screws are eliminated, you possibly can fastidiously elevate the microwave off of the wall and set it apart.
As soon as the microwave is eliminated, you possibly can disconnect {the electrical} wires which can be related to it. Watch out to not harm the wires, as this might create a fireplace hazard. As soon as the wires are disconnected, you possibly can take away the microwave fully. If you’re planning to maneuver the microwave to a brand new location, be sure you pack it fastidiously to keep away from harm. You may additionally need to take into account hiring knowledgeable that will help you transfer the microwave, particularly if it’s a heavy mannequin.
Disconnecting the Energy Provide
### 1. Shut off the electrical energy to the microwave.
Earlier than you start any work, it’s essential to make sure your security by disconnecting the facility provide to the microwave. Find {the electrical} panel in your residence and flip the circuit breaker that corresponds to the microwave circuit to the “OFF” place. It’s also possible to unplug the microwave from {the electrical} outlet whether it is related to 1.
### 2. Look forward to the microwave to chill down.
As soon as the facility provide is disconnected, enable the microwave to chill down for at the least half-hour earlier than trying to take away it. That is to stop any burns from residual warmth within the equipment.
### 3. Take away the mounting screws.
After the microwave has cooled, find the mounting screws that safe it to the wall or cupboard above it. These screws can normally be discovered on the highest or backside of the microwave, relying on the mannequin. Use a screwdriver to take away these screws, however don’t take away the microwave from the wall or cupboard but.
### 4. Help the microwave whereas eradicating it.
With the mounting screws eliminated, you might be able to take away the microwave from its place. Get somebody that will help you elevate and assist the microwave when you fastidiously slide it out of the wall or cupboard. Be conscious to not drop or harm the equipment throughout this course of.
Eradicating the Mounting Screws
As soon as the facility has been disconnected, you possibly can start eradicating the mounting screws. These screws are sometimes situated on the high of the microwave, on both aspect of the unit. They could be coated by plastic caps or covers, which you’ll gently pry off with a flathead screwdriver.
Utilizing a Phillips head screwdriver, fastidiously loosen the mounting screws by turning them counterclockwise. Don’t take away the screws fully at this level, because the microwave continues to be hooked up to the wall by {the electrical} wire and bracket.
As soon as the mounting screws are unfastened, you possibly can gently pull the microwave ahead and away from the wall. Watch out to not pull too onerous, as you could harm {the electrical} wire or bracket.
| Device Required | Steps |
|---|---|
| Flathead screwdriver | Pry off plastic caps or covers |
| Phillips head screwdriver | Loosen mounting screws |
| Gently pull microwave ahead | Detach from wall |
Unplugging the Wiring Harness
Unplugging the wiring harness is a vital step in eradicating an overhead microwave. It requires cautious consideration to element to make sure security and forestall harm to the equipment. Listed below are the steps concerned:
1. Flip Off Energy and Unplug the Microwave
Earlier than touching any electrical parts, make sure the microwave is disconnected from the facility provide. Find {the electrical} outlet and unplug the microwave from the wall. Don’t yank or pull on the wire, as this will harm the wiring.
2. Find and Entry the Junction Field
The junction field is a metallic enclosure that incorporates {the electrical} connections for the microwave. It’s sometimes situated inside the cupboard or behind the microwave itself. Entry the junction field by unscrewing the duvet or eradicating any bolts or screws holding it in place.
3. Unplug the Wiring Harness
After you have entry to the junction field, you will note a bundle of wires related to the microwave’s wiring harness. Every wire is often recognized by a special shade. To unplug the wiring harness, observe these steps fastidiously:
- Determine Terminals: Find the terminals on the junction field the place the wires from the wiring harness are related. Terminals are sometimes labeled or color-coded.
- Loosen Screws: Utilizing a screwdriver, loosen the screws on the terminals to launch the wires from the wiring harness.
- Pull Wires: Gently pull every wire straight out of the terminal. Don’t pull on the wire itself, as this will harm the wire or the terminal.
- Disconnect Harness: As soon as all of the wires are disconnected, fastidiously elevate the wiring harness away from the junction field.
Seek advice from this desk for a extra detailed visible information to unplugging the wiring harness:
| Step | Description |
|---|---|
| 1 | Determine terminals and loosen screws. |
| 2 | Pull wires straight out of terminals. |
| 3 | Disconnect wiring harness from junction field. |
Eradicating the Trim Plate
The trim plate is the ornamental panel that covers the sides of the microwave oven and conceals its mounting screws. To take away the trim plate, observe these steps:
1. Unplug the microwave oven from {the electrical} outlet.
2. Find the screws that maintain the trim plate in place. They’re sometimes situated on the highest and backside of the trim plate.
3. Take away the screws utilizing a screwdriver. Watch out to not drop the screws.
4. Gently pull the trim plate away from the microwave oven. It ought to come off simply.
5. If the trim plate is caught, you could want to make use of a putty knife or a skinny, flat object to softly pry it unfastened. Insert the putty knife or flat object between the trim plate and the microwave oven and punctiliously pry the trim plate away from the oven. Watch out to not harm the trim plate or the microwave oven.
As soon as the trim plate is eliminated, you should have entry to the mounting screws that maintain the microwave oven in place. Now you can proceed to the subsequent step of the removing course of.
Disassembling the Microwave
PREPARATIONS
Earlier than disassembling the microwave, guarantee energy provide is reduce off, plug is faraway from socket, and the gadget is chilly.
REMOVING THE CABINET
Determine the mounting screws or bolts securing the microwave to the cupboard. Unscrew or unbolt them fastidiously. Grip the microwave firmly, elevate it straight up off the cupboard, and set it apart.
DISCONNECTING THE WIRING
Find the wiring harness connecting the microwave to the facility provide and cupboard. Disconnect the harness by unplugging the connectors or unscrewing the terminals. Label wires if crucial for simpler reassembly.
REMOVING THE MOUNTING BRACKETS
Unfasten the mounting brackets attaching the microwave to the wall or ceiling. These could also be secured with screws or bolts; use applicable instruments to take away them.
DETACHING THE DOOR
Open the microwave door absolutely. Find the hinges connecting the door to the microwave physique. Unscrew or unbolt the hinges and punctiliously elevate the door off the microwave.
ACCESSING THE INTERNAL COMPONENTS
As soon as the door is eliminated, you possibly can entry the interior parts of the microwave. These could embrace the magnetron, waveguide, fan motor, and turntable motor. Deal with parts gently to keep away from harm.
ELECTRICAL COMPONENTS
MAGNETRON
The magnetron is a vacuum tube that generates microwaves. It’s situated within the base of the microwave oven and is chargeable for heating the meals. The magnetron is a crucial element and will solely get replaced by a professional technician.
WAVEGUIDE
The waveguide is a metallic tube that carries microwaves from the magnetron to the cooking chamber. You will need to preserve the waveguide clear and freed from obstructions.
FAN MOTOR
The fan motor circulates air contained in the microwave oven to chill the parts and forestall overheating. The fan motor is normally situated behind the microwave oven.
TURNTABLE MOTOR
The turntable motor rotates the turntable contained in the microwave oven, guaranteeing that meals is cooked evenly. The turntable motor is normally situated within the backside of the microwave oven.
Cleansing the Microwave
1. Unplug the microwave.
Earlier than you start cleansing, be sure you unplug the microwave from {the electrical} outlet. This may stop the microwave from by accident turning on while you’re cleansing it.
2. Take away the turntable and turntable ring.
The turntable and turntable ring might be eliminated by merely lifting them out of the microwave. Make sure you wash this stuff in sizzling, soapy water and dry them completely earlier than changing them.
3. Clear the inside of the microwave.
The inside of the microwave might be cleaned with a light detergent and water. Use a sponge or material to wipe down the inside surfaces, together with the door, the ceiling, and the edges. Make sure you rinse the inside completely with clear water and dry it with a clear material.
4. Clear the outside of the microwave.
The outside of the microwave might be cleaned with a light detergent and water. Use a sponge or material to wipe down the outside surfaces, together with the door, the edges, and the highest. Make sure you rinse the outside completely with clear water and dry it with a clear material.
5. Clear the door gasket.
The door gasket is a rubber seal that helps to maintain the microwave door closed. Over time, the door gasket can turn into soiled and greasy. Use a sponge or material to wipe down the door gasket with a light detergent and water. Make sure you rinse the door gasket completely with clear water and dry it with a clear material.
6. Clear the vent.
The vent is situated on the highest or aspect of the microwave. It’s used to exhaust air from the microwave. Over time, the vent can turn into clogged with mud and particles. Use a vacuum cleaner to scrub the vent. Make sure you take away any mud or particles from the vent.
7. Clear the microwave filter.
The microwave filter is situated behind the vent. It’s used to entice grease and smoke from the microwave. Over time, the microwave filter can turn into clogged with grease and smoke. You will need to clear the microwave filter usually to make sure that the microwave is working correctly. To wash the microwave filter, take away it from the microwave and wash it in sizzling, soapy water. Make sure you rinse the microwave filter completely with clear water and dry it completely earlier than changing it.
| Cleansing Activity | Frequency |
|---|---|
| Clear the inside of the microwave | Month-to-month |
| Clear the outside of the microwave | Month-to-month |
| Clear the door gasket | Month-to-month |
| Clear the vent | Each 3 months |
| Clear the microwave filter | Each 6 months |
Reinstalling the Microwave
1. Flip off the facility to the microwave on the circuit breaker.
2. Take away the mounting screws that maintain the microwave to the cupboard.
3. Fastidiously elevate the microwave off the mounting bracket.
4. Take away the facility wire from the outlet.
5. Take away the exhaust duct from the microwave.
6. If the microwave is vented outdoors, take away the vent cap from the outside wall.
7. Clear the mounting floor and the again of the microwave.
8. Apply a bead of caulk across the perimeter of the mounting floor. This may assist to seal the microwave and forestall drafts.
| Step | Motion |
|—|—|
| 1 | Flip off the facility to the microwave on the circuit breaker. |
| 2 | Take away the mounting screws that maintain the microwave to the cupboard. |
| 3 | Fastidiously elevate the microwave off the mounting bracket. |
| 4 | Take away the facility wire from the outlet. |
| 5 | Take away the exhaust duct from the microwave. |
| 6 | If the microwave is vented outdoors, take away the vent cap from the outside wall. |
| 7 | Clear the mounting floor and the again of the microwave. |
| 8 | Apply a bead of caulk across the perimeter of the mounting floor. This may assist to seal the microwave and forestall drafts. |
9. Place the microwave on the mounting bracket and align the screw holes.
10. Insert the mounting screws and tighten them securely.
11. Join the facility wire to the outlet.
12. Set up the exhaust duct to the microwave.
13. If the microwave is vented outdoors, set up the vent cap on the outside wall.
14. Activate the facility to the microwave on the circuit breaker.
15. Check the microwave to ensure it’s working correctly.
Reconnecting the Energy Provide
Step 1: Unplug the Microwave.
Earlier than touching any wires, make sure that the microwave is totally disconnected from the facility supply. Find the facility wire and pull the plug from the wall outlet.
Step 2: Determine the Wires.
Inside {the electrical} field, you can find a number of wires related to the microwave. These wires will sometimes be black, white, and inexperienced (or naked copper) and are held along with wire nuts.
Step 3: Take away the Wire Nuts.
Fastidiously take away the wire nuts by twisting them counterclockwise. Be cautious to not harm the wires.
Step 4: Separate the Wires.
As soon as the wire nuts are eliminated, gently separate the black and white wires from one another. The inexperienced (or naked copper) wire is the bottom wire and will stay related.
Step 5: Join the New Microwave.
Align the wires from the brand new microwave with the corresponding wires from {the electrical} field. Twist the black wire from the brand new microwave with the black wire from the field, and do the identical for the white wires.
Step 6: Safe the Wire Nuts.
Place a brand new wire nut over every set of twisted wires and tighten it clockwise till comfortable. Be sure that the wires are securely related.
Step 7: Check the Wiring.
Earlier than reconnecting the facility, double-check your connections utilizing a multimeter to make sure correct continuity and no brief circuits.
Step 8: Reconnect the Energy.
Plug the microwave energy wire again into the wall outlet and activate the breaker or fuse to revive energy to the equipment.
Step 9: Check the Microwave.
Press the facility button on the microwave to make sure that it’s functioning appropriately. If the microwave doesn’t activate or operates abnormally, repeat the above steps to test for any unfastened connections or wiring errors.
Testing the Microwave
Earlier than trying to take away the microwave, it is essential to make sure it is turned off and unplugged from the facility supply. Comply with these steps to confirm the microwave’s standing:
1. Examine the Energy Change
Find the facility swap on the microwave’s entrance or aspect panel. Be sure it is turned to the “Off” place.
2. Unplug the Microwave
Find {the electrical} outlet the place the microwave is plugged in. Firmly grasp the plug and pull it straight out of the outlet.
3. Look forward to Capacitor to Discharge
After unplugging the microwave, enable a couple of minutes for the capacitor to discharge. This may stop any electrical shock hazard.
4. Open the Microwave Door
As soon as the capacitor has discharged, open the microwave door to launch any remaining power.
5. Examine for Residual Warmth
Really feel the within and outdoors of the microwave to make sure it is fully cool. If it is nonetheless heat, wait longer earlier than continuing.
6. Visually Examine the Microwave
Study the microwave for any harm or unfastened elements. Should you discover something uncommon, don’t try to take away it your self and make contact with a professional equipment restore technician.
7. Collect Obligatory Instruments
You’ll seemingly want a Phillips head screwdriver and a flathead screwdriver to take away the microwave.
8. Put on Protecting Gear
Placed on security glasses and gloves to guard your self from sharp edges or electrical parts.
9. Disconnect Electrical Wires
As soon as the microwave is faraway from the wall, fastidiously disconnect {the electrical} wires from the terminal block. Word the place of every wire for reconnection later.
10. Take away the Mounting Bracket
Find the mounting bracket that secures the microwave to the wall. Utilizing the suitable screwdriver, take away the screws or bolts that maintain the bracket in place. Watch out to not drop the microwave when eradicating it from the bracket.
How To Take away A Overhead Microwave
Eradicating an overhead microwave is usually a daunting job, however it’s positively attainable to do it your self with the appropriate instruments and somewhat little bit of know-how. Listed below are the steps on how you can do it:
- Flip off the facility to the microwave. This may be finished by unplugging it from the outlet or by turning off the breaker that controls the facility to the microwave.
- Take away the mounting screws. There are normally 4 screws that maintain the microwave in place. These screws are situated on the highest of the microwave, close to the again. Use a screwdriver to take away the screws.
- Fastidiously elevate the microwave off of the wall. As soon as the screws are eliminated, you possibly can fastidiously elevate the microwave off of the wall. Make sure you assist the load of the microwave together with your different hand.
- Disconnect the wiring. As soon as the microwave is off of the wall, it’s worthwhile to disconnect the wiring. There are normally two wires that join the microwave to the facility supply. Use a pair of pliers to disconnect the wires.
- Take away the microwave from the kitchen. As soon as the wiring is disconnected, you possibly can take away the microwave from the kitchen. Make sure you elevate the microwave fastidiously and keep away from bumping it into something.
Individuals Additionally Ask About How To Take away A Overhead Microwave
How do I take away a microwave from a cupboard?
To take away a microwave from a cupboard, you’ll need to:
- Open the cupboard door.
- Find the screws which can be holding the microwave in place.
- Take away the screws.
- Fastidiously elevate the microwave out of the cupboard.
How do I take away a microwave from a wall bracket?
To take away a microwave from a wall bracket, you’ll need to:
- Flip off the facility to the microwave.
- Take away the screws which can be holding the microwave to the wall bracket.
- Fastidiously elevate the microwave off of the wall bracket.
- Disconnect the wiring from the microwave.
How do I take away a inbuilt microwave?
To take away a inbuilt microwave, you’ll need to:
- Flip off the facility to the microwave.
- Take away the trim across the microwave.
- Take away the screws which can be holding the microwave in place.
- Fastidiously elevate the microwave out of the cupboard.
- Disconnect the wiring from the microwave.
