Wrapping your bike handlebars is an easy however efficient manner to enhance your driving expertise. It may possibly present further consolation, grip, and magnificence. If you happen to’re new to wrapping handlebars, don’t be concerned – it is a comparatively simple course of that may be accomplished in a couple of hours. On this article, we’ll stroll you thru the steps of find out how to wrap bike handlebars like a professional.
Earlier than you begin, you will want to assemble a couple of provides. You will want a roll of handlebar tape, a pair of scissors, and a small quantity of rubbing alcohol. You may additionally wish to use a hair dryer to assist the tape adhere higher. Upon getting your provides, you are prepared to start out wrapping.
Step one is to scrub your handlebars. This can assist the tape adhere higher. Use a small quantity of rubbing alcohol on a clear rag to wipe down the bars. As soon as the bars are clear, you can begin wrapping the tape. Begin by putting the tip of the tape within the middle of the handlebar. Then, wrap the tape across the bar, overlapping every layer by about half an inch. As you wrap, you should definitely hold the tape tight and even. While you attain the tip of the handlebar, use the scissors to chop the tape after which tuck the tip underneath the earlier layer.
Overlapping the Tape
To create a cushty and safe grip, overlapping the handlebar tape is essential. Observe these steps meticulously:
1. Begin with the Left Facet:
Start by putting the tape’s finish on the left finish of the handlebar, roughly 1 inch from the sting. Safe it with electrical tape or glue.
2. Wrap Away from the Physique:
Wind the tape away from you, protecting it taut however not too tight. Intention for an overlap of roughly 1/2 to 1 inch on every wrap.
3. Anchor the Tape:
When you attain the tip of the handlebar, fold the tape over itself and safe it with a couple of wraps {of electrical} tape.
4. Begin the Proper Facet:
Repeat the method on the appropriate facet, beginning on the periphery and wrapping in the direction of the middle of the handlebar.
5. Overlap the Center:
When the right-side tape reaches the center of the handlebar, overlap it barely over the left-side tape. Use 4 to six wraps to firmly safe the overlap. This creates a “bullhorn” form that enhances grip and luxury.
| Wrap Layers | Beginning Place | Ending Place | Overlap |
|---|---|---|---|
| 1-2 | Left finish | Proper finish | 1/2 – 1 inch |
| 3-4 | Proper finish | Center | 1/2 – 1 inch |
| 5-6 | Center | Left facet | 4 – 6 wraps |
How To Wrap Bike Handlebars
Wrapping your bike handlebars is an effective way to enhance the consolation and magnificence of your bike. It is also a comparatively simple and cheap undertaking that you are able to do your self with a couple of fundamental instruments. Listed below are the steps on find out how to wrap bike handlebars:
-
Collect your supplies. You will want the next supplies to wrap your bike handlebars:
- Bar tape
- Electrical tape
- Scissors
- A Phillips head screwdriver
- A hex key
- A torque wrench (elective)
-
Take away the outdated bar tape. In case your handlebars are already wrapped, you’ll need to take away the outdated bar tape earlier than you’ll be able to wrap new tape on. To do that, use a Phillips head screwdriver to take away the brake lever clamps and the shifter clamps. Then, fastidiously peel off the outdated bar tape.
-
Clear the handlebars. As soon as the outdated bar tape is eliminated, clear the handlebars with a humid material to take away any grime or particles.
-
Wrap {the electrical} tape. Begin by wrapping electrical tape across the handlebars, beginning on the middle and dealing your manner out in the direction of the ends. Wrap {the electrical} tape tightly and overlap every layer by about half. {The electrical} tape will assist to guard the handlebars from the wear and tear and tear of the bar tape.
-
Wrap the bar tape. Begin by wrapping the bar tape on the middle of the handlebars, overlapping {the electrical} tape by about half. Wrap the bar tape tightly and overlap every layer by about half. Proceed wrapping the bar tape till you attain the tip of the handlebars.
-
Safe the bar tape. As soon as the bar tape is wrapped, use electrical tape to safe it in place. Begin by wrapping {the electrical} tape across the handlebars on the middle, after which work your manner out in the direction of the ends. Wrap {the electrical} tape tightly and overlap every layer by about half.
-
Reinstall the brake lever clamps and the shifter clamps. As soon as the bar tape is secured, reinstall the brake lever clamps and the shifter clamps. Tighten the clamps utilizing a torque wrench to the producer’s specs.
-
Get pleasure from your newly wrapped handlebars! Your bike handlebars are actually wrapped and able to experience.
Individuals Additionally Ask About How To Wrap Bike Handlebars
How usually ought to I wrap my bike handlebars?
You must wrap your bike handlebars each time they begin to present indicators of wear and tear and tear. This may very well be as a result of bar tape changing into frayed, torn, or soiled. If you happen to experience your bike continuously, chances are you’ll must wrap your handlebars each few months or so.
What sort of bar tape ought to I exploit?
There are numerous various kinds of bar tape out there, every with its personal distinctive properties. Among the hottest varieties of bar tape embrace:
* Cork tape: Cork tape is a pure materials that’s snug to grip and absorbs vibrations.
* Artificial tape: Artificial tape is constructed from a wide range of supplies, together with rubber, plastic, and foam. Artificial tape is commonly extra sturdy than cork tape, nevertheless it can be much less snug to grip.
* Leather-based tape: Leather-based tape is an opulent materials that’s each snug to grip and sturdy. Nonetheless, leather-based tape may be dearer than different varieties of tape.
How do I select the appropriate dimension bar tape?
The width of the bar tape ought to match the width of your handlebars. You possibly can measure the width of your handlebars by measuring the space between the 2 ends of the handlebars. As soon as you realize the width of your handlebars, you’ll be able to select the suitable dimension bar tape.
